(818) 818-6559
Free Shipping over $25
 
Toggle Nav
My Cart
Search
  • My Account
  • My Wish List
  • Sign In
  • Create an Account

GW7511 | Pentair GW7700 PoolShark Pool Cleaner Bumper Kit Gray

$34.99
In stock
SKU
GW7511
- +
Ask a Question

Ask a Question

GW7511 | Pentair GW7700 PoolShark Pool Cleaner Bumper Kit Gray

SKU#: GW7511

Pentair Bumper Kit Gray for GW7700 PoolShark  Automatic Pool Cleaner GW7511

$34.99
  • Bumper replacement kit
  • Fits Pentair PoolShark automatic cleaner model GW7700
  • Available in gray color
  • Includes right bumper boot clip, right bumper boot, bumper, left bumper boot and left bumper boot clip
  • Measures 9-1/4-inch length by 4-1/2-inch width by 2-3/4-inch height

Ask a Question
See Details
GW7511 | Pentair GW7700 PoolShark Pool Cleaner Bumper Kit Gray GW7511 | Pentair GW7700 PoolShark Pool Cleaner Bumper Kit Gray GW7511 | Pentair GW7700 PoolShark Pool Cleaner Bumper Kit Gray
GW7511 | Pentair GW7700 PoolShark Pool Cleaner Bumper Kit Gray
  • Product Details

    About this product

    Description

    Disassembly
    1. With a screwdriver, carefully work the rubber vacuum pad down over the lip of the Outer Housing, (see Figure 25).
    2. Lift the Outer Housing straight up off of the chassis. Squeeze the tabs on the Bumper/Height Limiter Clips (inside the housing) to remove the Bumper/ Height Limiter. The Bumper/Height Limiter, Bumper/Height Limiter Boots, and Bumper/Height Limiter Clips pull apart, (see Figure 26).
    3. Squeeze and pull the Sprocket Clips to release the Drive Shaft Assembly and Center Sprocket, (see Figure 27).
    4. Pull the Oscillator Straight out from the bottom of the Outer Housing. Be careful not to lose the Sliding Seals, (see Figure 28).
    5. Squeeze the latching tabs and pull up on the Swivel Housing and Swivel. The assembly will come up, releasing the Swivel Sprocket. Squeeze the latching tabs to remove the Clutch Clip, (see Figure 29).
    6. Remove the Shaft Plug with the stainless steel shaft and the Large Steering Drive Assembly, (see Figure 30).
    7. Remove the Oscillator Sleeve, releasing the Oscillator Sleeve Bushing and the Clutch assembly, (see Figure 31)

    Highlights

    Features

    • Bumper replacement kit
    • Fits Pentair PoolShark automatic cleaner model GW7700
    • Available in gray color
    • Includes right bumper boot clip, right bumper boot, bumper, left bumper boot and left bumper boot clip
    • Measures 9-1/4-inch length by 4-1/2-inch width by 2-3/4-inch height

    Brand Information

    Founded in 1966, Pentair has engineered water solutions to filter, clean and sanitize water to its purest state, while automation equipment makes it all easy to control from anywhere so that you can truly enjoy your pool and spa.

    Visit Manufacturers Website
  • Specifications

     

    Problem Corrective Action
    Square Bottom Pools Only: If the transition radius between your pool's floor and wall is small and the PoolShark will not climb the pool walls, then you have a  square bottom pool. If so, remove the cleaner from the pool and drill two holes in the indentations in the bumper (see Figure 33). This will provide an outlet for air which would otherwise accumulate in the hollow bumper. This air, from microscopic bubbles suspended in the pool water, is normally able to escape when the PoolShark climbs the pool walls.
  • Q/A
    No Questions
WARNING! The following product(s) can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov