619818Z | Pentair Intellibrite Light Engine Kit

$579.99
Out of stock
SKU
619818Z
Ask a Question

Ask a Question

619818Z | Pentair Intellibrite Light Engine Kit

SKU#: 619818Z

Pentair Light Engine Kit for Intellibrite 5G Color LED Pool And Spa Lights 619818Z 

$579.99

REMOVING THE LIGHT CIRCUIT BOARD ASSEMBLY

1. Using a 1/4 in (0.64 cm) nut driver, carefully remove the four retainer nuts from the light assembly (see illustration on next page). Place the nuts aside for reinstallation.
2. Unplug the two connector plugs from the circuit board. Lift up the circuit board and remove it from the light housing base.
3. Carefully lift off the old thermal strips from the base of the light housing base and discard.
4. Place the two new thermal strips (provided) over the circuit board studs in the base of the light housing.
5. Place the light circuit board over the base studs and seat the circuit board on top of the thermal strips. Be sure the two connecting wires are not caught between the housing and the edge of the circuit board.
6. Using a 1/4 in (0.64 cm) nut driver, tighten each of the four retaining nuts to a torque value of 6.0 (minimum) to 8.0 (maximum) in-lbs to secure the circuit board.

INSTALLATION AND USER’S GUIDE

Ask a Question
619818Z | Pentair Intellibrite Light Engine Kit 619818Z | Pentair Intellibrite Light Engine Kit 619818Z | Pentair Intellibrite Light Engine Kit
619818Z | Pentair Intellibrite Light Engine Kit
  • Product Details

    About this product

    Description

    1. Install NEW GASKET ONTO LENS: Stretch the gasket around the circumference of the lens. Be sure the gasket is installed evenly around the lens.
    2. ALIGN THE LENS/GASKET ON TO THE LIGHT HOUSING:
    a) With the light housing resting on its base, place the lens/gasket on top of the light housing.
    b) Rotate the lens/gasket to align the letter “W” (“WIDE” angle) on the lens with the brass nut in the housing (see diagram on page 17 for brass nut location).
    3. INSTALL THE FACE RING: Place the face ring on top of the lens/gasket/housing. Rotate the face ring so the pilot screw hole is aligned in the 12 o’clock position, with the lens letter “W” (or “N”) and the brass nut in the housing. Also, verify the “TOP” position arrow indicator label (see page 17) on the rear of the housing is aligned with the pilot screw on the face ring.

    Highlights

    1.Using your fingers, carefully disconnect each fuse connector plug from the circuit board terminals. Carefully lift each connector plug upward, with small side-to-side movements while holding the circuit board terminals with a flat screw driver. Then gradually disconnect the connector plug from the terminal.
    Note: To avoid permanent damage to the circuit board, be sure not to pull the terminals off the surface of the circuit board.
    2. Once the fuse connector plugs are removed from the circuit board terminals, separate the fuse assembly from the light wire harness by pressing down on the fuse release lever, then gently pull apart.

    Features

    REMOVING THE LIGHT CIRCUIT BOARD ASSEMBLY

    1. Using a 1/4 in (0.64 cm) nut driver, carefully remove the four retainer nuts from the light assembly (see illustration on next page). Place the nuts aside for reinstallation.
    2. Unplug the two connector plugs from the circuit board. Lift up the circuit board and remove it from the light housing base.
    3. Carefully lift off the old thermal strips from the base of the light housing base and discard.
    4. Place the two new thermal strips (provided) over the circuit board studs in the base of the light housing.
    5. Place the light circuit board over the base studs and seat the circuit board on top of the thermal strips. Be sure the two connecting wires are not caught between the housing and the edge of the circuit board.
    6. Using a 1/4 in (0.64 cm) nut driver, tighten each of the four retaining nuts to a torque value of 6.0 (minimum) to 8.0 (maximum) in-lbs to secure the circuit board.

    INSTALLATION AND USER’S GUIDE

    Brand Information

    Founded in 1966, Pentair has engineered water solutions to filter, clean and sanitize water to its purest state, while automation equipment makes it all easy to control from anywhere so that you can truly enjoy your pool and spa.

    Visit Manufacturers Website
  • Specifications

  • Q/A
    No Questions
WARNING! The following product(s) can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov